1/10 Scale Camaro LS3 motor. Working model

Description

Summary Update: after checking the scale it is actually closer to 1/10 scale. maybe a little larger. Update: 11/23/2017 Added spark plugs, LS3 coils, Coil boot and spark plug boot. Coil Boots may have to enlarged depending on your printer settings. Spark plug boot is mis-labeled. the 90 degree boot goes to the plugs as seen in the pictures. 1/10 scale Camaro LS3 motor. this is a scaled down version of ericthepoolboy's 1/3 scale motor. The 1/10 scale down was initally done by Novel Mutations and redesigned by me to use 623 (10x3x4mm) bearings and 1.5mm screws. Screws can be sourced from www.rc4wd.com, ebay, or amazon. Most of the 1.5 screws I used was 1.5x 3mm (covers and surface screws, 6mm (crank bearing caps side bolts and Crank spacers), 8mm (crank), and 10mm (flywheel). Bearings were sourced from here https://www.banggood.com/10pcs-623ZZ-3x10x4mm-Ball-Bearings-Shielded-Radial-Bearings-p-1049663.html?rmmds=myorder&cur_warehouse=CN 1x2mm Neodymium magnets hold all the parts together. I found them on ebay. The drive motor was sourced from a old HS-645 MG servo I had lying around. The drive gear is simply pushed on with a little CA glue. Cams have to be printed with full support and bearing mounts need to be filed and sanded when done for a flush fit I used #18 brad nails and CA glue to assemble the cam. The Air filter is printed out of TPU and is secured with a indent on the Air filter throttle body. It you are going to use PLA you migh have to file off the indent on the airfilter. This is not a easy build. Expect to file, sand, shave, alter, and drill to make this build a working build. All the lifter holes have to be ported and the push rod holes have to be sized to what you are going to use. the pistons and the cylinders have to be sanded smooth. You tube video https://youtu.be/NvuUL0jqNSs Novel Mutations version can be found here.. https://www.thingiverse.com/thing:1996991 Rolling engine stand can be fount here... https://www.thingiverse.com/thing:2657483

Design Files

File Size

LS3_Motor_crank_7.stl
134 KB
sparkplug_boot_22RE.stl
37.6 KB
Throttle_body_for_air_filter.stl
302 KB
Cylinder_Head.stl
5.68 MB
LS3_Motor_starter_gear.stl
73.8 KB
Crankshaft_Output_Flange.stl
151 KB
LS3_Motor_cam_spacer.stl
17.4 KB
LS3_Header_-_Driver_Side.stl
1.75 MB
LS3_Motor_cam_set.stl
521 KB
Timing_Cover.stl
964 KB
LS3_Motor_starter_mount.stl
106 KB
LS3_Motor_lifter.stl
63.3 KB
Valley_Plate.stl
201 KB
sparkplug_22RE.stl
218 KB
LS3_Motor_crank_mount_2.stl
95.5 KB
Stand_-_Front_Crossmember.stl
252 KB
LS3_Motor_oil_filter.stl
96.7 KB
LS3_Motor_connecting_rod_and_cap.stl
86.5 KB
LS3_Motor_crank_3.stl
143 KB
Timing_Chain_Tensioner.stl
15.3 KB
LS3_Motor_piston.stl
84.8 KB
Stand_-_Rear_Crossmember.stl
269 KB
LS3_Motor_crank_2.stl
144 KB
LS3_Motor_crank_4.stl
101 KB
LS3_Motor_crank_mount_1.stl
84.9 KB
Rocker_Rail.stl
117 KB
Oil_Pan.stl
932 KB
Rear_Main_Cover.stl
491 KB
LS3_Motor_oil_intake.stl
1.79 MB
Exhuast_Valve_2.stl
126 KB
Flywheel_drive_teeth.stl
785 KB
Engine_Block_-_No_Supports.stl
19 MB
KN_airfilter.stl
129 KB
distributor_boot_22RE.stl
94.3 KB
LS3_coil_.stl
134 KB
Engine_Block_-_With_Supports.stl
19.2 MB
LS3_Motor_throttle_body.stl
219 KB
LS3_Header_-_Passenger_Side.stl
1.75 MB
LS3_Motor_crank_5.stl
111 KB
LS3_Motor_crank_8.stl
119 KB
Valve_Cover_Drivers_Side.stl
719 KB
Stand_-_Center_Rib.stl
288 KB
LS3_Motor_cam_gear_large.stl
202 KB
LS3_Motor_crank_gear.stl
126 KB
Valve_Cover_Passenger_Side.stl
560 KB
LS3_Motor_spring_cap.stl
26.4 KB
LS3_Motor_crank_6.stl
144 KB
Intake_Valve_2.stl
137 KB
Rocker_Arm.stl
80.3 KB
LS3_Motor_crank_1.stl
135 KB
LS3_Motor_throttle_body_valve.stl
59.3 KB
Lifter_Guide.stl
78.2 KB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×