3D Printable DJI Inspire V1.5

Prints (1)

Description

Summary Want a DJI Inspire One but don't want to spend $3K? Then this is the 3D printing project for you! The cost of building the frame and landing gear is only around $100. Add your electronics and get in the air for far less than DJI would charge. This is my project that evolved from the idea RCHobbiesUK developed. The RCGroups community took off from their inspiration and mutated their design into an entirely new beast that has considerable improvements. The full list of options, print settings, print checklist, hardware, electronics, wiring, and everything else can be read in full at the RCGroups thread http://www.rcgroups.com/forums/showthread.php?t=2399740#post31442294 The complete set of modeling files is on that page as well! So if you want to put your own twist on my design you won;t need to start from scratch.

Design Files

File Size

Boom_Lift_Linkage_Sweep_1.stl
40.3 KB
Canopy_Nose_FPV_V1.5.stl
457 KB
Boom_Outer_Joint_2_20Deg_R.stl
1.58 MB
Boom_Outer_Joint_1.stl
449 KB
Wormdrive_V1.5_for_Quarter-20_Nut.stl
56.9 KB
Wormdrive_V1.5_M8Round.stl
107 KB
Wormdrive_V1.5_for_M5_Nut.stl
56.1 KB
Wormdrive_Endstops_V1.5_M8Round.stl
155 KB
Wormdrive_Endstops_V1.5_for_M8_Nut.stl
106 KB
Servo_Cap_M8.stl
74 KB
Frame_Receiver_Shelf_90mm_V1.5.stl
442 KB
Frame_Top_V1.5.stl
433 KB
Frame_Motor_ESC_Box_RC-CAM.stl
114 KB
Frame_Joint_Bushing_V1.5.stl
20 KB
Frame_Bushing_Holder_Front_V1.5.stl
503 KB
Frame_38mm_Strut.stl
62.6 KB
Canopy_Top_V1.5_Split_A.stl
474 KB
Wormdrive_Endstops_V1.5_M8Octo.stl
110 KB
Wormdrive_Endstops_V1.5_for_M5_Nut.stl
105 KB
LED_Clip_V2.stl
218 KB
Gimbal_Plate_Diam_40mm_X.stl
159 KB
Gimbal_Frame_V1.5.stl
130 KB
Frame_Strengthener_V1.5.stl
56.8 KB
Frame_Motor_Foot_1_V1.5.stl
556 KB
Frame_Motor_Mount_V1.5.stl
468 KB
Frame_Bushing_Holder_Rear_V1.5.stl
600 KB
Frame_Bottom_V1.5.stl
351 KB
Canopy_Top_V1.5_Split_B.stl
127 KB
Clamp_Angle_Guide.stl
22.5 KB
Boom_Outer_Joint_2_20Deg_L.stl
1.58 MB
Boom_Rod_Linkage_20Deg_L.stl
16.9 KB
Boom_Lift_Linkage_Sweep_2.stl
39 KB
Boom_Joint_20Deg_R.stl
1.31 MB
Boom_Support_Linkage_V4_2pc.stl
65.3 KB
Canopy_Tail_V1.5.stl
162 KB
Drill_Guide_V1.5.stl
377 KB
Boom_Joint_20Deg_L.stl
1.31 MB
Boom_Rod_Linkage_20Deg_R.stl
16.9 KB
Boom_Stop_Ring_V3_2pc.stl
83.3 KB
Drill_Guide_for_Wood_Screw.stl
16.5 KB
Frame_Base_Plate_90mm_V1.5.stl
322 KB
Frame_Motor_Foot_2_V1.5.stl
583 KB
Servo_Cap_M5.stl
43.4 KB
Wormdrive_Endstops_V1.5_for_Quarter-20_Nut.stl
105 KB
Wormdrive_V1.5_for_M8_Nut.stl
58.1 KB
Wormdrive_V1.5_M8Octo.stl
62 KB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×