CoLiDo DIY

12 Reviews

5 star
5
4 star
6
3 star
1
2 star
0
1 star
0
Small 13062223 583189981843542 5509447774481468297 n By james_taylor1 on Oct 20 2016
For £175 CAN'T BEAT IT!!

diy took 15minutes to assemble. Easy setup with software. Up and printing in under 2hours!! Bargain  to start with. This is just what you need for your 1st printer. So you can learn whats the main points of a 3d printer that can you can learn , so if you want to buy a better one then This is your first port of call 

5****

Small nikola tesla 1 By Trinova on Oct 25 2016
Best Intro printer for the price

The software included is easy to use and is an all in one stop for slicing printing and calibrating. The printer came in few parts that made it easy to put together in about 15-20 minutes. I did find it hard to find information on using the printer with other software than what is included. Since this is my first 3d printer I do want to say the build quality is very good. For under $300 this printer is great I have learned so much from it so far. The prints come out as nice as the makerbot one and sometimes even better at my college.

Avatar small By Peter Engelbertz on Dec 06 2016
My first printer ColiDo

I was amazed how quickly the entry with Colido and the software went. In a short time I had the first result, first with models from the Internet afterwards with own models. It was an advantage that I worked with CadCam. What I would like to say is, I am 67 years old and already 4 years pensioner. As a hobby, I run a tin foundry and visit 4-5 craft shops where I sell my parts, at the last markets I took the 3D printer and showed it. It was a great success, the people stood up to 15Meter snake. Peter Engelbertz

Avatar small By Palladius on Jan 10 2017
Great for someone new to 3D printing

I received this printer as a gift. The setup was quick and pretty straight forward. The calibration card they send is a litte too thick for getting a good first layer. Calibrate to the thickness of paper in all four corners. If you can't, realign the axes. If adhesion issues remain a quick wipe of the blue tape solves it. I had a good first success with simple prints but ran into problems with more complicated ones. I had to tighten the y-axis belt and the prints got beautiful. This is a fantastic printer so far and I'm very pleased. I plan on upgrading to a heated bed and probably adding an LCD. The control board is setup to receive both but the heated bed will up the power consumption. Requiring a new power supply.

Avatar small By oe8pck on Jul 24 2017
Complete Beginner.

I have been using this printer for one day and one night. It has been running constantly. I have not had one bad print. I am a complete beginner and am delighted that all works so well. Got to get some more filament :-)

It was very easy to assemble and calibrate, I use hairspray on thee blue tape and this ensures that the part sticks well to the table but it can be removed without damaging the tape.

All in all I think I made a perfect choice.

Avatar small By bmd1 on Aug 27 2017
Total beginner.

I wanted a printer but the one I wanted was a lot of money for me so when this printer came up at a really good price I thought well even if I don't get on too well at least I haven't lost a lot. I have to say I was not disappointed, the printer was easy to put together the instructions easy to understand and the software - Slic3r- easy to use. So far the only bad prints have been my error. There are mods that can be done to improve the quality and the best bit is you can print them yourself. I bought a heated bed kit, unfortunately no instructions with it but there are several tutorials on You Tube so not a problem.

Would I recommend it to my friends- most certainly based on my experience so far.

Avatar small By Kenbot on Dec 29 2017
googlefu mastery recommended

the software is supposed to come with slic3r settings bundled in for easy beginners. I never found them. So I used my Googlefu and read some of the gcode from the bundled models and created my own. Still some tweaking to do but it simply is a lot of fun. 

The fun models take a long time. But that is par for the course in this 3d printing world.  Don’t just take my word for it. Get one yourself and go crazy. 

Avatar small By minnes on Jan 25 2018
I love this printer!

This is a really inexpensive printer that is super easy to set up and produces great results! The only thing that I needed to tweak was the print settings because different prints require different speeds, temperatures, etc. The way you edit these settings seems pretty daunting at first, but if you spend some time with it it becomes easy to understand. I would definitely recommend this printer for anyone looking for an inexpensive printer with a large print area that is really easy to use. 

Avatar small By ethansymons5 on Feb 25 2018
printer is great

i like this printer

Avatar small By steven_orr1 on Mar 23 2018
seems pretty good!

this being my first 3D printer it seems to be going ok and working well enough for me to figure out whats going on. i would recommend this as a good cheap printer.  

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×