The Universal Spool Holder - Main Page

Prints (0)

Description

This is the main page for my universal spool holder design... This page contains every single file I have made and every derivative of the holder... I'm going to lay out instructions on how to get the perfect fit for your spools in the instruction tab... You can also watch the YouTube video below where I explain everything you need to know... https://www.youtube.com/watch?v=zG1CFx9aUIk&feature=youtu.be There are three "sizes" (different length arms) for this spool holder... Every arm length is on this page in STL form, but to make it simpler and to avoid confusion, I made three separate pages for each sized holder (Small, Standard, Oversized)... When you watch the video or read the instructions you know what measurements to take to get the perfect fit... On a side note, if you want a truly, all around "Universal" holder - you can simply print two "OverSized" Arms and 110mm Rods... This will fit damn near every spool - it just wont be a tailored fit - and thus wont look pretty... This is why I decided to make three sizes - strictly for aesthetic reasons. Small - http://www.thingiverse.com/thing:1001360 Standard - http://www.thingiverse.com/thing:943563 OverSized - http://www.thingiverse.com/thing:1001359 This is a full redesign of my popular, but old and relatively weak spool holder that I designed nearly two years ago... Old, Obsolete Spool Holder: http://www.thingiverse.com/thing:290064 This new design is 100% better - I completely redesigned my screws and spinner bolts for better tolerance for 3D Printing... My old screws were good if they were machined, but they were way too fine to be 3D printed well... So I made the threading much better and made the screws much stronger... I also added a lot of structural features that I explain in the video... Here's a list of what I did in the new design. Made both arms (the base and the spinner) 2.5mm shorter in height, I also added fillets to every corner so every contour is nice and rounded. Redid the bolt pattern and made that easier on the hand while spinning the spinner bolt. Increased the diameter of the screws and added 45 degree chamfers for strength... Screws are very strong now. Redid all the threading... This will thread smooth and tight right off the printer - I had 100% success rate on prints. Added a hole on the lower Rods to hold ends of filament to keep them from unraveling or raveling in - resulting in getting the spool tangled up. This is now about a 33% decrease in total print time from my old design... Overall, it should take about 6-7 hours to print an entire holder on a standard .2mm layer setting... But you can speed it up by going .3mm and everything will be perfect... Infill is not a big issue... 15-20% should do it... If you want everything to look nice on the outside - do 3 perimeter shells. Other than all of that - this should work for everyone and will fit on 95% of spools... The only spool I know doesn't fit on this univeral holder is Taulman brand spools... But never fear, I made a spool holder specifically for Taulman Spools... You can find the Taulman spool holder here... http://www.thingiverse.com/thing:938437 **I hope you find this spool holder useful... Thanks for reading... ENJOY!!! FilamentChallenge

Design Files

File Size

40mm_BigRod.STL
1.27 MB
OverSized_BigTop_SpinnerArm.STL
3.64 MB
OverSized_SmallTop_BaseArm.STL
2.1 MB
110mm_SmallRod.STL
1.57 MB
90mm_SmallRod.STL
1.66 MB
70mm_BigRod.STL
1.14 MB
73mm_BigRod.STL
1.08 MB
60mm_BigRod.STL
1.14 MB
60mm_SmallRod.STL
1.8 MB
45mm_BigRod.STL
1.27 MB
40mm_SmallRod.STL
2.04 MB
50mm_BigRod.STL
1.19 MB
67mm_BigRod.STL
1.14 MB
55mm_SmallRod.STL
1.79 MB
67mm_SmallRod.STL
1.78 MB
75mm_BigRod.STL
1.06 MB
73mm_SmallRod_HatchBox.STL
1.73 MB
80mm_BigRod.STL
1.17 MB
75mmSmallRod.STL
1.66 MB
85mm_SmallRod.STL
1.67 MB
105mm_BigRod.STL
1.03 MB
95mm_SmallRod.STL
1.66 MB
100mm_SmallRod.STL
1.66 MB
105mm_SmallRod.STL
1.57 MB
OverSized_BigTop_BaseArm.STL
2.07 MB
Small_BigTop_SpinnerArm.STL
3.53 MB
OverSized_SmallTop_SpinnerArm.STL
3.51 MB
Standard_SmallTop_BaseArm.STL
2.12 MB
Small_SmallTop_SpinnerArm.STL
3.52 MB
Standard_BigTop_SpinnerArm.STL
3.73 MB
Standard_SmallTop_SpinnerArm.STL
3.26 MB
Standard_BigTop_BaseArm.STL
2.06 MB
Small_BigTop_BaseArm.STL
2.07 MB
Small_SmallTop_BaseArm.STL
2.14 MB
110mm_BigRod.STL
1.03 MB
100mm_BigRod.STL
1.05 MB
95mm_BigRod.STL
1.04 MB
85mm_BigRod.STL
1.06 MB
90mm_BigRod.STL
1.05 MB
80mmSmallRod.STL
1.7 MB
65mm_SmallRod.STL
1.85 MB
70mm_SmallRod.STL
1.73 MB
65mm_BigRod.STL
1.12 MB
50mm_SmallRod.STL
1.84 MB
45mm_SmallRod.STL
1.98 MB
55mm_BigRod.STL
1.15 MB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×