OpenR/C Formula 1 car

Prints (30)

Description

Please respect the license under which this project is released. Thank you!

Add your car to the OpenRC buildmap: https://zeemaps.com/map?group=1888242

This is the OpenR/C Formula 1 car.  It´s the third generation OpenR/C car and this time around focus is on simplicity! You can print everything in PLA except the tires which are done in NinjaFlex! Of course you can print it in any material you like but for those that want to print a car but only have PLA at hand, this is the project for you!

A note on the servo saver. It´s designed to be used with PLA, the upper and lower BOM applies force similar to a spring in a convetional servo saver. Of course the pressure depends on the type of material used, infill etc. Fine tuning can be done adding washer under or over the servo saver.

The "Main Turning Vane´s" needs to have it´s lower part trimmed using a "exacto knife". Then slide it the chassie plate and push it over the "Lid" and it should snap into place-

Any questions can be made in the Facebook group here: https://www.facebook.com/groups/1111886228841596/

Or in the Google+ Community here: https://plus.google.com/u/0/communities/112745535...

Complete hardware/electronics kit is available here: http://www.3dprintnpack.com/product-page/4054b44d-0bfb-cfed-4661-451da35810da

Parts that need support added:

Front Spoiler.stl

Front.stl

Rear Rim.stl

Rear Wing.stl

Servo Saver Lower.stl

Things to buy:

Ok, obviously you need some filament which you´ll get from your favourite filament supplier.

You also need M3 screws and nuts which you can get at your local hardware store. Check the BOM list for what to get.

Some bearings are needed aswell, check the BOM list or buy a kit from FastEddyBearings.com

Last but not least you need electronics and here´s what i got, all from HobbyKing:

ESC and motor combo

Battery

Micro Servo This is what i bought and i think it´s not very good, please let me know if you have a better revommendation.

Transmitter and Receiver (i use something else but this is a "cheap" alternative)

If you are new to this whole R/C hobby you´ll also need a LiPo charger for the battery. Ask in the Google + Community for recommendations.

Full assembly STEP file is available here: https://dl.dropboxusercontent.com/u/6748864/OpenR...

Rain tires designed by Thomas Palm are available here.

Low profile rimas & tires designed by Thomas Palm are available here.

Making "donuts"... =) (video)

Like my FaceBook page - https://www.facebook.com/Danie...

Subscribe to my YouTube channel - https://www.youtube.com/user/D...

INSTAGRAM https://www.instagram.com/dani...

TWITTER https://twitter.com/DanielNore...

GOOGLE+ https://plus.google.com/u/1/+D...

FACEBOOK https://www.facebook.com/danie...

GOOGLE+ OPENRC COMMUNITY https://plus.google.com/commun...

FACEBOOK OPENRC GROUP https://www.facebook.com/group...

Design Files

File Size

Tire_V2.stl
448 KB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Front_Upper.stl
54.3 KB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Nose_Lower.stl
619 KB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Front_Lower.stl
1.38 MB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Lid_Lower.stl
1.39 MB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Lid_Upper.stl
196 KB
RackMultipart20160530-141-15ezsch.zip/Dual_Extr_Nose_Upper.stl
40.4 KB
RackMultipart20160530-141-15ezsch.zip/OpenRC_F1_Dual_Extrusion_Files.png
137 KB
Front Rim For F104 Tire.stl
309 KB
Rear Rim For F104 Tire.stl
587 KB
Tire-NinjaTek.stl
1.21 MB
Dual_Extr_Front_Lower.stl
1.38 MB
Dual_Extr_Front_Upper.stl
69.2 KB
Dual_Extr_Lid_Lower.stl
1.37 MB
Dual_Extr_Lid_Upper.stl
183 KB
Dual_Extr_Nose_Lower.stl
626 KB
Dual_Extr_Nose_Upper.stl
47.8 KB
Lock Pin.stl
37.4 KB
Wheel Axle Holder Right.stl
259 KB
Chassie Assembly.pdf
193 KB
Front BOM Assembly.pdf
260 KB
Front Wheel Assembly.pdf
187 KB
OpenRC F1 BOM ver01 - Sheet1.pdf
64.6 KB
Rear Axle Assembly.pdf
191 KB
Rear Wheel Assembly.pdf
123 KB
Nose.stl
587 KB
Front Spoiler.stl
583 KB
Chassie Front.stl
348 KB
Wheel Axle Holder Left.stl
516 KB
Front Lower BOM.stl
58.6 KB
Servo Saver Upper.stl
289 KB
Rear Wheel Axle.stl
385 KB
Motor Cover.stl
1.24 MB
Front Rim.stl
176 KB
Front BOM Block.stl
38.8 KB
Camera.stl
356 KB
Steering Pin.stl
21.4 KB
Spur Gear.stl
247 KB
Servo Saver Lower.stl
311 KB
Rear Wing.stl
226 KB
Rear View Mirror Left.stl
818 KB
Rainlight and Diffuser.stl
782 KB
Pinion Gear.stl
93.8 KB
Front Top BOM.stl
64.4 KB
Front Wheel Axle.stl
255 KB
Front Wheel Hub.stl
263 KB
Front.stl
1.37 MB
Lid.stl
1.2 MB
Main Turning Vane Left.stl
119 KB
Main Turning Vane Right.stl
119 KB
Rear Rim.stl
349 KB
Rear View Mirror Right.stl
818 KB
Servo Holder.stl
241 KB
Tire.stl
527 KB
Wheel Lock Nut.stl
65.5 KB
Center Body.stl
1.22 MB
Chassie Rear.stl
384 KB

Comments

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×